About Us

Hand Made Quality Golf Products...
customized and made your way at reasonable prices. 

Our custom clubs are analyzed, measured and built to the very highest standards to remove any manufacturing imperfections from them so you can play a better game of golf with more consistent equipment. Although we have only the best products from the best companies in the world, they are manufactured to industry standards and assembled to industry standards. We adjust the weights and flexes and align the shafts so that all of the manufacturing tolerances are reduced to near perfection in each or our hand crafted match sets. 

• Industry standard flexes are 10 cycles per minute (cpm) on a frequency analyzer - we fit flex to 2 cpm standards
• Most shafts are measured by butt flex - we measure in 7 position on wood shafts to adjust the butt, mid section and tip flexes to your swing
• Shaft manufacturing may leave shafts with different flex measurements if measured in all 360° or orientation - we align the shaft in the optimum position for maximum consistency and center face contacts. This gives you more consistent yardage and dispersion from side to side on each shot.
• Head weights from the factory have a 7 gram per head progression with a plus or minus 2 gram difference allowing for a wide range of swing weights in each set manufactured without correction. - We make weight corrections to insure exact swing weights throughout the set. 
• MOI measurements - We even go a step further and adjust our sets to Moment of Inertia measurements that are far more exacting than swing weight and play much better.
• Proper length is important for hitting each shot in the center of the club face as well as allowing for proper swing path. We measure your swing path and face angle with our electronic equipment to insure you have the proper length for your golf swing. We make allowances for plus or minus 2 inch deviation from standard off the rack fitting.
• Proper Weight and Balance is also important for not only correct swing path but for correct face angle at impact. We use our electronic equipment to measure and fit you to the proper total weight, swing weight or MOI and balance point at the proper length for your golf swing to allow for your best swing path and face angle at impact. 

Orders outside the United States will be shipped by United States Postal Service if possible. Orders exceeding the Priority Mail Large Box will be shipped via UPS. Please do not select USPS shipment for golf clubs, you have to use UPS for golf clubs.

Equipment by:

• Adams Golf - Custom Fitting Center
• Callaway Golf - Custom Fitting Center
• Cleveland - Fitting Center
• Nicklaus Golf - Certified Premium Custom Fitting Center 
• Srixon - Fitting Center
• Alpha Golf - Certified Custom Fitting Center
• Infiniti Golf - Certified Custom Fitting Center
• Wishon Golf Technologies - Certified Custom Fitting Center
• many, many others, too numerous to list

Shafts by:

• Aldila
• Aerotech
• ACCRA
• OBAN 
• Fierce
• UST
• FST
• True Temper
• Rifle
• KBS
• S K Fiber
• Tom Wishon Golf Technologies
• Swing Science
• Enzo
• And many more, too numerous to list
  
  Quality Assurance & Benefits of shopping at McNix Golf:

• The quality of our premium heads and shafts are equal to or better than any on the market.
• Our workmanship compares to the highest quality hand crafted custom work you will find anywhere.
•  We ship free to the Continental United States
• We sell a number of National Brands like Callaway, Cleveland, Srixon, Hogan, Top Flite, Hippo and others
• Ourl boutique brands equal or surpass the quality of virtually any clubs made the way we build them
• Our clubs are built one club at a time and built to match all clubs in the set
• We do not mass produce any golf equipment and we do not have an assembly line
• The standard for flex is considered to be 10 cpms between flexes, our premium custom fitted boutique brand sets are fitted to a 2 cpm standard
• Our our premium custom fitted boutique brand sets are flex matched to sort shafts electronically and align them in the order that works best for the golfer
• We find the spine in all shafts, and test them electronically so we can insert them in the club to remove manufacturing abnormalities

Online Custom Fitting Help
When you order choose the options that best fit your golf shots and add any additional information in the comments at check out.

• Choose all options for Right Hand Golfers
• Knowing if you draw, hook, fade or slice will help us determine both the best total weight and swingweight (MOI) for your club(s)
• Knowing if your shot starts to the right or left will also help us determine the best total weight and swingweight (MOI) for your club(s)
• Knowing if you hit every shot from the center of your stance, off your left heel or off your left toe will help us advise you on best loft
• Knowing your wrist to floor measurement will help us determine the best length for you clubs
• Knowing your release timing will help us with your shaft flex
• Knowing if you hit the ball high or low will help us with your shaft flex
• All the information requested will help us make your club a better fit and is worth the extra cost if we can build to your specifications.
• If you choose the custom fit option we will email you with additional questions about your selections and will be begin ordering the parts of construction until you have agreed to the build.

Please allow at least 2 weeks for custom product shipping. We attempt to keep items in stock but sometimes we run out of some popular items and have to reorder to produce your custom product. In the event our vendor is also out of a product we will notify you of any additional delays by email. When the product is in stock we will ship as soon as it is assembled.

Every effort is made to list items and price items correctly but all listings are not guaranteed.  Items found to be listed incorrectly will not be honored when ordered. When such an item is ordered we will notify the buyer and inform them of the correct listing and price and the customer will have the opportunity to puchase the item or items at the correct price or quantity as it should be listed or receive a refund of the payment sent. 

A complete Repair Facility

Staffed by Roy Nix - Association of Golf Clubfitting Professionals Master and Daniel McMahon,- AGCP Level 10 Qualified clubmaker.
Roy Nix attended PGA School way back in 1968 and has been a Head Professional, Teaching Professional and now is a Master craftsman at Custom Clubfitting and club building. Roy is assisted by Daniel McMahon who is a skilled craftsman in his own right. Daniel does most of the repair work and some of the building of custom clubs. 

We have the latest in state-of-the-Art electronic equipment and all the experience necessary to measure, analyze, and repair almost any golf club. We have access to almost any shaft you may want or need and many of the best brand names in the industry, and we are adding brands constantly to improve our services to golfers.  

Retail Golf Shop

Our new shop has over 4,000 square feet and we have a complete golf shop to serve you. If you do not see a product, please email us at info@mcnixgolf.com and ask for it. We will try and get it for you.  

Winner Regions Charity Classic
Keith Fergus plays the Alpha V5 LX driver to win both the Cap Cana Championship and Regions Charity Classic